Neverending fermentation...
Moderator: slothrob
-
- Pale Ale
- Posts: 68
- Joined: Sat Mar 02, 2002 11:49 am
- Location: Roscoe, IL, US
Neverending fermentation...
This is a follow up to my earlier Cold Yeast.. posting. The brew has been in the primary for a week now and is still bubbling about every 10-20 seconds. I took a gravity reading just to see where I was at and it is 1.026. Predicted final gravity is supposed to be 1.013. Is there anything I should do to help, or just continue to wait it out?
-
- Double IPA
- Posts: 170
- Joined: Fri Sep 07, 2001 1:56 am
I think your yeast 'hit the wall'.
Hardcore,
I think now is the time to add more yeast. If you are reasonably sure that the batch is not contaminated you should make a small (1 quart) starter and repitch. Do not over do it with the amount. You are just trying to drop the SG a fraction of the oroginal value.
As I stated before viability is the key to preventing stuck fermentations. New yeast needs to be acclimated to their new environment (higher gravities require more live yeast). Oxegenation of the wort is the second deciding factor. This helps the yeast form flexible membrains that enable them intake the nutrients from the wort and excreet waste by products to the wort (some wanted and some not wanted). Temperature ,if held within the range, will help regulate cell growth, reproduction and the amount of esters excreeted into the wort.
Sanitize the outside of your fermenter, open it in a clean room (avoid dust and drafts) and repitch some more yeast. Keep writting your notes for the next brew.
Good brewing,
Tom F.
I think now is the time to add more yeast. If you are reasonably sure that the batch is not contaminated you should make a small (1 quart) starter and repitch. Do not over do it with the amount. You are just trying to drop the SG a fraction of the oroginal value.
As I stated before viability is the key to preventing stuck fermentations. New yeast needs to be acclimated to their new environment (higher gravities require more live yeast). Oxegenation of the wort is the second deciding factor. This helps the yeast form flexible membrains that enable them intake the nutrients from the wort and excreet waste by products to the wort (some wanted and some not wanted). Temperature ,if held within the range, will help regulate cell growth, reproduction and the amount of esters excreeted into the wort.
Sanitize the outside of your fermenter, open it in a clean room (avoid dust and drafts) and repitch some more yeast. Keep writting your notes for the next brew.
Good brewing,
Tom F.
-
- Pale Ale
- Posts: 68
- Joined: Sat Mar 02, 2002 11:49 am
- Location: Roscoe, IL, US
Hey Tom...What If I...?
What if I rack the brew to the secondary fermenter, then take some of the remaining yeast slurry, mix it with some corn sugar and pure water, let it get going, then pitch that to my secondary?
-
- Strong Ale
- Posts: 339
- Joined: Sat Mar 17, 2001 11:33 pm
- Location: Hummelstown, PA, US
Irish Red
My irish red got down to 1.022 and it refuses to go any farther. Its only supposed to go down to 1.019, so its not as far off as yours. I'll bottle in a day or two when I have the time, but I'm not too worried about it, it will taste just fine.
Yeast energizer
Have you tried yeast energizer, or yeast nutrient?
Sometimes the sugar content is too high, and the yeast needs additional other nutrients to help them out. Also, If there are to many unfermentables, you can try some amalaze enzyme. If I question the amount of unfermentables, I usually put some of this in a pitching time to help convert unfermentable to fermentables.
Sometimes the sugar content is too high, and the yeast needs additional other nutrients to help them out. Also, If there are to many unfermentables, you can try some amalaze enzyme. If I question the amount of unfermentables, I usually put some of this in a pitching time to help convert unfermentable to fermentables.