Calculating Mash Efficiency

General discussion on BeerTools Pro Software.
rfoushee
Posts: 1
Joined: Tue Sep 30, 2008 4:27 pm

Calculating Mash Efficiency

Post by rfoushee » Tue Sep 30, 2008 4:46 pm

My apologies in advance if this issue has been addressed in the past. I searched the archives and didn't really find any informative answer.

I've been using ProMash for years, and one feature I always use for a brew session is the ability to measure my mash efficiency using my preboil volume.

I've downloaded the demo of BTP 1.5, and after spending a number of hours getting comfortable with the software and it's methods, I find I like it quite a bit.

The one thing I can't figure out how to do though, is calculate my efficiency based on a preboil gravity. I know you can hover over the 'Kettle Volume @ 212) value to get the tooltip for the estimated preboil gravity, and I'm also aware of the analysis tab where I can enter my postboil figures, but again, that's not exactly what I'm looking for.

I'm looking for a method to enter a preboil volume and a gravity reading, and have it calculate the efficiency. Can this be accomplished with BTP?

Thanks!

User avatar
slothrob
Moderator
Moderator
Posts: 1834
Joined: Mon Apr 10, 2006 1:36 pm
Location: Greater Boston

Re: Calculating Mash Efficiency

Post by slothrob » Tue Sep 30, 2008 8:55 pm

Set your preboil volume and adjust the mash efficiency value until the pre-boil volume (from the hover) matches the measured gravity. When the gravity is right, you've calculated your efficiency.
BTP v2.0.* Windows XP

derfburg21
Light Lager
Light Lager
Posts: 23
Joined: Thu Dec 28, 2006 3:59 pm
Location: Fort Smith, AR

Post by derfburg21 » Fri Oct 31, 2008 3:24 pm

This makes no sence, can someone help me out here. Preboil vol is "Kettle Vol @ 212"?

User avatar
Legman
Strong Ale
Strong Ale
Posts: 349
Joined: Sat Dec 08, 2007 8:02 pm
Location: North Carolina

Kettle Volume

Post by Legman » Fri Oct 31, 2008 7:50 pm

Preboil volume is "Kettle Volume".
Set your preboil volume and adjust the mash efficiency value until the pre-boil volume (from the hover) matches the measured gravity. When the gravity is right, you've calculated your efficiency.
What Slothrob is saying, is to take you mouse pointer and hold it over the "Kettle Volume" and the preboil gravity will pop up.

User avatar
slothrob
Moderator
Moderator
Posts: 1834
Joined: Mon Apr 10, 2006 1:36 pm
Location: Greater Boston

Re: Kettle Volume

Post by slothrob » Fri Oct 31, 2008 10:07 pm

Legman wrote:Preboil volume is "Kettle Volume".
Set your preboil volume and adjust the mash efficiency value until the pre-boil volume (from the hover) matches the measured gravity. When the gravity is right, you've calculated your efficiency.
What Slothrob is saying, is to take you mouse pointer and hold it over the "Kettle Volume" and the preboil gravity will pop up.
Thanks, Legman. Yeah, I meant... 'until the pre-boil gravity (seen from hovering over the "Kettle Volume") matches the measured gravity'.

It seemed to make sense when I typed it :oops:
Last edited by slothrob on Sat Nov 01, 2008 9:47 am, edited 1 time in total.
BTP v2.0.* Windows XP

User avatar
Legman
Strong Ale
Strong Ale
Posts: 349
Joined: Sat Dec 08, 2007 8:02 pm
Location: North Carolina

Mash Efficiency

Post by Legman » Sat Nov 01, 2008 7:56 am

Slothrob, I knew exactly what you meant. I'm just glad you did say that, 'cause I had never tried that before........and ya know what? My mash efficiency SUCKS!!! :x :x :x

I've gotta get my system dialed in better. I just recently started using a cooler mash tun, so it's all part of the learning process, I suppose.

User avatar
slothrob
Moderator
Moderator
Posts: 1834
Joined: Mon Apr 10, 2006 1:36 pm
Location: Greater Boston

efficiency

Post by slothrob » Sat Nov 01, 2008 9:58 am

Glad to be helpful.
It took me a while to get my efficiency up where I was happy with it. I got a big increase with an improved crush, and a number of smaller incremental increases from improvements like minimizing dead volume and an optimized sparge.
BTP v2.0.* Windows XP

User avatar
Legman
Strong Ale
Strong Ale
Posts: 349
Joined: Sat Dec 08, 2007 8:02 pm
Location: North Carolina

Re:Efficiency

Post by Legman » Sat Nov 01, 2008 1:06 pm

I'm still getting my grains milled at my local HBS. So I can't control that at this point. But X-mas time is coming......I may have to put in for a new grain mill! :mrgreen:

derfburg21
Light Lager
Light Lager
Posts: 23
Joined: Thu Dec 28, 2006 3:59 pm
Location: Fort Smith, AR

Post by derfburg21 » Mon Nov 03, 2008 9:44 am

OK, I'm stupid, still can not make this work.

derfburg21
Light Lager
Light Lager
Posts: 23
Joined: Thu Dec 28, 2006 3:59 pm
Location: Fort Smith, AR

Post by derfburg21 » Mon Nov 03, 2008 9:51 am

Can someone post a screen cap please?

derfburg21
Light Lager
Light Lager
Posts: 23
Joined: Thu Dec 28, 2006 3:59 pm
Location: Fort Smith, AR

Post by derfburg21 » Mon Nov 03, 2008 4:10 pm

OK, I know for a fact I got a 1.078 Preboil reading. Where does that go and how does that relate to this. My OG reading was 1.039.

Image

User avatar
slothrob
Moderator
Moderator
Posts: 1834
Joined: Mon Apr 10, 2006 1:36 pm
Location: Greater Boston

mash efficiency

Post by slothrob » Mon Nov 03, 2008 5:42 pm

Your pre-boil gravity was 1.078 and your post boil was 1.039?
Something's not right.

If you started with 6.75 gallons at 1.039 and ended with 6 gallons, your final gravity was 1.044.

If your pre-boil gravity was 1.039, then your efficiency of 62.8% would be correct.
BTP v2.0.* Windows XP

User avatar
jawbox
Imperial Stout
Imperial Stout
Posts: 530
Joined: Fri Oct 27, 2006 1:43 pm
Location: W. Dundee

Post by jawbox » Wed Nov 05, 2008 11:17 am

something doesn't make any sense
iMac 27", 3.4 GHz Intel Core i5, 8GB Ram, Mac OSX 10.12.6
iPhone 7+
iPad Pro 10.5
I like macs ;)

Bobby_M
Light Lager
Light Lager
Posts: 46
Joined: Tue Feb 05, 2008 11:14 am

Post by Bobby_M » Wed Nov 05, 2008 3:20 pm

Are you talking literally about MASH efficiency (how well you covert) or do you mean total preboil mash/lauter efficiency (how well you convert AND extract)? You mention a gravity reading of 1.078 and the only thing I can think of is that you're measuring first runnings gravity.
Bobby_M on Homebrewtalk.com
HP DV9200 Laptop, Intel T5500, 2 Gig RAM, Windows Vista, 17" widescreen display at 1440 x 900 and 32 colors.

my youtube vids: www.youtube.com/bobbyfromnj

User avatar
jeff
Imperial Stout
Imperial Stout
Posts: 1508
Joined: Sun Jan 09, 2000 8:16 pm
Location: Hollywood, SC
Contact:

Post by jeff » Wed Nov 05, 2008 10:15 pm

derfburg21 wrote:OK, I know for a fact I got a 1.078 Preboil reading. Where does that go and how does that relate to this. My OG reading was 1.039.
I know this is probably a stupid question, but, did you perhaps have a 10.78 Plato reading rather than a 1.078 gravity reading? :?
Jeff
BeerTools.com Staff

Post Reply