New Brewing Research Conclusions....
Moderator: slothrob
-
- Posts: 3
- Joined: Mon Feb 12, 2001 9:33 pm
Mash Thickness
Hi Eric,
Thanks for the reply.
I am a little confused, are you saying that thicker mashes convert faster than thinner mashes?? I always thought it was the other way round (to a point) ie a mash thickness of 2.5:1 will convert slower than 3:1, mainly due to product inhibition effects being greater in thicker mashes.
A reason to mash thinner is to overcome the issue of uneven mash temperature. At 2.5:1 it is much harder to stir the mash than it is at 3:1.
I performed another mash yesterday before I had a chance to read your reply. I reduced my roller mill gap to 0.75mm and mashed at 3.2:1 thickness, I got conversion in about 25-30min @ 68-69C, so its close. Previously it took more like 40-45min, but I was milling more coarsely (0.9mm gap).
Had no problems runoff, but that was mainly due to conditioning the malt with a little water (15-20mL per kg) prior to milling. If I don't do this and mill at such a fine setting the husks are shredded too much.
I will give your recommended 2.8:1 ratio a go next time.
Thanks again
Cheers
Petr
Thanks for the reply.
I am a little confused, are you saying that thicker mashes convert faster than thinner mashes?? I always thought it was the other way round (to a point) ie a mash thickness of 2.5:1 will convert slower than 3:1, mainly due to product inhibition effects being greater in thicker mashes.
A reason to mash thinner is to overcome the issue of uneven mash temperature. At 2.5:1 it is much harder to stir the mash than it is at 3:1.
I performed another mash yesterday before I had a chance to read your reply. I reduced my roller mill gap to 0.75mm and mashed at 3.2:1 thickness, I got conversion in about 25-30min @ 68-69C, so its close. Previously it took more like 40-45min, but I was milling more coarsely (0.9mm gap).
Had no problems runoff, but that was mainly due to conditioning the malt with a little water (15-20mL per kg) prior to milling. If I don't do this and mill at such a fine setting the husks are shredded too much.
I will give your recommended 2.8:1 ratio a go next time.
Thanks again
Cheers
Petr
-
- Posts: 3
- Joined: Mon Feb 12, 2001 9:33 pm
One Small Question
Eric,
Once you have finished making your yeast how do you seperate it from the 2.5L of (oxidised) beer?
Thanks
Petr
Once you have finished making your yeast how do you seperate it from the 2.5L of (oxidised) beer?
Thanks
Petr
- Mesa Maltworks
- Strong Ale
- Posts: 477
- Joined: Tue Sep 11, 2001 11:16 pm
- Location: Georgetown, Grand Cayman Island
Not really an issue...
There will be no flavor transference by using this starter, it is too small a volume and since it did not undergo fermentation and never received excessive oxygen (if you did it right) the oxidative effects upon the alcohols should not have occured.
Eric
Eric
- billvelek
- Imperial Stout
- Posts: 801
- Joined: Fri Mar 05, 2004 9:44 am
- Location: Arkansas, USA
- Contact:
You the man! Thanks for all your effort.
You cleared up everything just fine. Very nice of you to spend so much time with me, and I can only hope that there are a few others who have been helped by all of the time that you spent on this.
Thank you VERY much.
Cheers.
Bill Velek
Thank you VERY much.
Cheers.
Bill Velek
Good Timing
Eric
I read your information and it really peaked my interest. I had just finished brewing a Bavarian Weizen and was about to brew a second 5 gal.batch After reading your information I said to my self, why not, I was in a perfect position to make a comparison between a 90 minute single infusion and a 20 minute infusion using the same recipe. Be advised that the iodine test showed sugar conversion at the end of 20 minutes.
Thanks
Tom
I read your information and it really peaked my interest. I had just finished brewing a Bavarian Weizen and was about to brew a second 5 gal.batch After reading your information I said to my self, why not, I was in a perfect position to make a comparison between a 90 minute single infusion and a 20 minute infusion using the same recipe. Be advised that the iodine test showed sugar conversion at the end of 20 minutes.
Thanks
Tom
pitching on a yeastcake
Assuming i've got well above the cellcount needed from a yeastcake, can I just go ahead and pitch unaerated wort on top? Or would you advise scooping up the yeast, making a starter with it, aerating it and then re-pitching?
Once you've got enough cells, that is, will the yeast need oxygen before it starts fermenting again after a rest, or is aeration solely to help the yeast reproduce?
Sorry if these are silly questions.
Corin
Once you've got enough cells, that is, will the yeast need oxygen before it starts fermenting again after a rest, or is aeration solely to help the yeast reproduce?
Sorry if these are silly questions.
Corin
Yeastcakes
My understanding, Corin, is the oxygen is needed only during the reproduction phase. Additionally, yeast will only reproduce until they reach a certain concentration per volume of wort--how they know when to stop budding I don't know. Therefore, aeration would be unnecessary if you have plenty of yeast as you're saying. Be prepared for an explosive ferment.
Hope this helps.
v/r
Bill
Hope this helps.
v/r
Bill
Corin
Hopefully it is a yeastcake from a secondary, and not the primary. Many will advise against repitching, but if your sanitation was good and you had good results from the present yeast, give the secondary yeast a try. Don't mess with the primary yeast, there is too much trub and potential for off flavors and infections are more prevalent with the primary.
yes it was
yep, pitched on a secondary cake of WLP833. seems to be going, slowly but surely...
New Brewing Research ?'s
Regarding Eric's post on 4/20 concerning brewing techniques, I checked conversion at 20 minutes and the iodine test was good, however I mashed another 20 minutes and got an additional seven gravity points. Had I not done that I woun'd have hit my efficiency target.
Does that mean I'll need to adjust my recipes to keep the same efficieny for a shorter sparge ?
Does that mean I'll need to adjust my recipes to keep the same efficieny for a shorter sparge ?
- Mesa Maltworks
- Strong Ale
- Posts: 477
- Joined: Tue Sep 11, 2001 11:16 pm
- Location: Georgetown, Grand Cayman Island
?s for your ?s...
"I checked conversion at 20 minutes and the iodine test was good, however I mashed another 20 minutes and got an additional seven gravity points."
Clarification needed here: Do you mean that the first wort gravity after recirculation was 7 points lower than after an additional 20 minutes rest and recirculation? And... what measurement are you using... potential points per pound in SG or Plato? What efficiency do you regularly achieve?
"Does that mean I'll need to adjust my recipes to keep the same efficieny for a shorter sparge ?"
This technique does not change sparge duration... you should always sparge for 45~60 minutes @ 168 F, stopping the lauter when the gravity is 2.5 plato.
Post back with more specifics so that I may assess what might have occured.
Eric
Clarification needed here: Do you mean that the first wort gravity after recirculation was 7 points lower than after an additional 20 minutes rest and recirculation? And... what measurement are you using... potential points per pound in SG or Plato? What efficiency do you regularly achieve?
"Does that mean I'll need to adjust my recipes to keep the same efficieny for a shorter sparge ?"
This technique does not change sparge duration... you should always sparge for 45~60 minutes @ 168 F, stopping the lauter when the gravity is 2.5 plato.
Post back with more specifics so that I may assess what might have occured.
Eric
-
- Pale Ale
- Posts: 77
- Joined: Tue May 13, 2003 7:01 pm
- Location: Lincoln, NE, US
Mesa...
Were the conclusions of the aforementioned research published in a professional journal of some kind? if so where can I go to read the article, assuming it is in English.
Thanks
Nate
Thanks
Nate
- Mesa Maltworks
- Strong Ale
- Posts: 477
- Joined: Tue Sep 11, 2001 11:16 pm
- Location: Georgetown, Grand Cayman Island
Research was published by Charlie Bamforth & Michel Lewi
The research I was exposed to was presented by Charlie Bamforth & Michael Lewis of UC Davis (mash & yeast topics) and a roundtable group of German Brewmasters & Dan Gordon from Gordon Biersch (first wort hopping) both of which were hosted at the Association of Brewer's 2004 Craftbrewing Conference in San Diego.
To read most of the info (some was concluded after the books), get Charlie Bamforth's book "Standards of Brewing: A Practical Approach to Consistency and Excellence " and Michael Lewis'/Tom Young's book "BREWING Second Edition". Both may be acquired at:
http://www.store.beertown.org/shopdispl ... al+Brewing
The German Brewmaster's roundtable was just that.... we asked random questions of interest, they answered.
Both of the sessions are available on CD from Treefarm Productions.
1. Blowing the Froth Off Some Brewing Fiction: Giving the True Story to the Next Breed of Brewers, Part I:
Speaker(s):
Professor Michael J. Lewis
Charles Bamforth, PhD
Charlie Bamforth takes time off from his central midfield responsibilities at Man. U. to shatter some of the inaccurate paradigms of the brewing world. Michael Lewis will share the stage during the Q & A.
https://treefarmtapes.safeserver.com/ca ... ctid=13489
2. Blowing the Froth Off Some Brewing Fiction: Giving the True Story to the Next Breed of Brewers, Part II
Speaker(s):
Professor Michael J. Lewis
Charles Bamforth, PhD
Annually our highest-rated presenter in conference surveys, Michael Lewis is well known for his ability to raise concepts that send brewers back to question established brewing concepts and investigate further in their own brewhouses. Charlie Bamforth will share the stage during the Q & A.
https://treefarmtapes.safeserver.com/ca ... ctid=13492
3. Lager Brewing Techniques Panel
Speaker(s):
Dan Gordon
Phil Markowski
Guido Waldecker
Phil Markowski leads a panel discussion of German brewers and lager expert Dan Gordon in discussing issues related to lager beer production.
https://treefarmtapes.safeserver.com/ca ... ctid=13499
If you get all of these sources, you will have available to you all that I was exposed to at the conference and I have read on the topics I dealt with in this thread.
Eric
[/url]
To read most of the info (some was concluded after the books), get Charlie Bamforth's book "Standards of Brewing: A Practical Approach to Consistency and Excellence " and Michael Lewis'/Tom Young's book "BREWING Second Edition". Both may be acquired at:
http://www.store.beertown.org/shopdispl ... al+Brewing
The German Brewmaster's roundtable was just that.... we asked random questions of interest, they answered.
Both of the sessions are available on CD from Treefarm Productions.
1. Blowing the Froth Off Some Brewing Fiction: Giving the True Story to the Next Breed of Brewers, Part I:
Speaker(s):
Professor Michael J. Lewis
Charles Bamforth, PhD
Charlie Bamforth takes time off from his central midfield responsibilities at Man. U. to shatter some of the inaccurate paradigms of the brewing world. Michael Lewis will share the stage during the Q & A.
https://treefarmtapes.safeserver.com/ca ... ctid=13489
2. Blowing the Froth Off Some Brewing Fiction: Giving the True Story to the Next Breed of Brewers, Part II
Speaker(s):
Professor Michael J. Lewis
Charles Bamforth, PhD
Annually our highest-rated presenter in conference surveys, Michael Lewis is well known for his ability to raise concepts that send brewers back to question established brewing concepts and investigate further in their own brewhouses. Charlie Bamforth will share the stage during the Q & A.
https://treefarmtapes.safeserver.com/ca ... ctid=13492
3. Lager Brewing Techniques Panel
Speaker(s):
Dan Gordon
Phil Markowski
Guido Waldecker
Phil Markowski leads a panel discussion of German brewers and lager expert Dan Gordon in discussing issues related to lager beer production.
https://treefarmtapes.safeserver.com/ca ... ctid=13499
If you get all of these sources, you will have available to you all that I was exposed to at the conference and I have read on the topics I dealt with in this thread.
Eric
[/url]
-
- Light Lager
- Posts: 37
- Joined: Sat Jul 31, 2004 11:26 am
- Location: WestCentral Ohio
This is great information...
#1. I have always added my first hopping after I have gotten the hot break to be skimmed off by me then added my first hop addition after a vigorous boil and that starts my 60 minute boil time schedule (and reduces the chance of a boilover).
#2. I have found that even with fully modified malts, a feable attempt at a protein rest will result in clearer beer but clear beer is not my main objective, but nice.
#3. I've always suspected that the cooled wort needed a bit of aeration but that the yeast was needing oxygen more so & when doing a starter I always splash the starter to aerate.
When I first read your profound info, I was thinking "Oh No! Next he's going to tell us the lead pipe rumor was just that"!
To sum it up...thanks for the info. I'm not a pro just a Passionate Hobbiest Homebrewer (PHH). Your pro help is awesome!
#1. I have always added my first hopping after I have gotten the hot break to be skimmed off by me then added my first hop addition after a vigorous boil and that starts my 60 minute boil time schedule (and reduces the chance of a boilover).
#2. I have found that even with fully modified malts, a feable attempt at a protein rest will result in clearer beer but clear beer is not my main objective, but nice.
#3. I've always suspected that the cooled wort needed a bit of aeration but that the yeast was needing oxygen more so & when doing a starter I always splash the starter to aerate.
When I first read your profound info, I was thinking "Oh No! Next he's going to tell us the lead pipe rumor was just that"!
To sum it up...thanks for the info. I'm not a pro just a Passionate Hobbiest Homebrewer (PHH). Your pro help is awesome!
Four More Beers!... Four More Beers!... Four More Beers! ...