Page 1 of 19

BeerTools Pro Bug Reports Archive A

Posted: Tue Oct 24, 2006 9:58 am
by lathe
BeerTools Pro Help System Bug RESOLVED

BeerTools Pro 1.0.1

A bug in the BeerTools Pro Windows installer has been identified and will prevent the help system from operating. We have fixed the installer and it is ready for download in your Download Manager. Sorry for any inconvenience this may have caused.

BeerTools Pro 1.0.1a resolves the issue.

Null in quantity field

Posted: Wed Oct 25, 2006 9:39 pm
by tjthresh
1. select a grain and add to the grain list.
2. Highlight the grain and make the quantity null.
3. Leaving the grain quantity null, adjust the final volume.

This resulted in the error
An exception of class NilObjectException was not handled. The application must shut down.

Re: Null in quantity field

Posted: Wed Oct 25, 2006 9:43 pm
by jeff
tjthresh wrote:1. select a grain and add to the grain list.
2. Highlight the grain and make the quantity null.
3. Leaving the grain quantity null, adjust the final volume.
Do you adjust the final volume numerically or with the arrows? Is the Lock/Scale checkbox checked? What about the kettle volume lock? Thanks!

Re: Null in quantity field

Posted: Wed Oct 25, 2006 11:11 pm
by tjthresh
jeff wrote:
tjthresh wrote:1. select a grain and add to the grain list.
2. Highlight the grain and make the quantity null.
3. Leaving the grain quantity null, adjust the final volume.
Do you adjust the final volume numerically or with the arrows? Is the Lock/Scale checkbox checked? What about the kettle volume lock? Thanks!
arrows
Final Vol is checked (lock/scale) Not sure whick the check box is connected too.

Posted: Thu Oct 26, 2006 6:22 pm
by JPinAZ
FWIW I tried this & did not get the error message.

Posted: Thu Oct 26, 2006 7:46 pm
by billvelek
JPinAZ wrote:FWIW I tried this & did not get the error message.
I didn't either, but I just got the program and maybe I'm not duplicating the steps. Still trying to find my way around it.

Bill Velek
www.2plus2is4.com

Posted: Fri Oct 27, 2006 10:08 am
by slothrob
There seems to be a bug in the Infusion Edit window in the Schedule section.

I've been using

Posted: Fri Oct 27, 2006 11:11 am
by jeff
[quote="slothrob"]There seems to be a bug in the Infusion Edit window in the Schedule section.

I've been using

Posted: Fri Oct 27, 2006 11:36 am
by slothrob
Sorry, should have taken better notes and I don't have it with me. I think it's the bottom most value, but I won't be able to check until I get home tonite.

Posted: Fri Oct 27, 2006 7:08 pm
by slothrob
It's when I set the Water Temp at 212, the Target Temp at 270, it displays the Water Volume, in this case, at 1.54 gallons. I hit OK, the window closes.

Then, when I open the window with the Edit button, the water volume now is displayed as 1.61 Gallons.

If I set the Water Temp and Volume, a Target Temp is displayed. If I close the window, hit Edit, the Water Volume has again changed.

Posted: Fri Oct 27, 2006 8:07 pm
by billvelek
slothrob wrote:It's when I set the Water Temp at 212, the Target Temp at 270, ... snip
I assume you mean 170, right?

Bill Velek

Posted: Fri Oct 27, 2006 9:15 pm
by slothrob
Ouch. Yeah, that's just a typo, I'm not trying to break the laws of physics or anything like that.

Saving Converted ProMash Files

Posted: Sun Oct 29, 2006 7:39 am
by ColoradoBrewer
I've run into a problem saving ProMash recipe files. Not sure if this is an actual bug, but I'll report what is happening anyway. When I try to save a recipe that was loaded from ProMash I get the following error message: "Assertion Failure: Assertion(!!(scrCharLens >0)) failed in output.cpp, line 995". My options are to Abort, Retry, or Ignore. I'm not sure if this is a bug because the subject files were ProMash Session files (.brw) converted within ProMash to recipe files (.rec). Now if I look in my folder of BTP recipes I will see the file, but when I try to load it I get an error that it is an invalid XML file (BTW, the file size is 0 bytes). I can save regular ProMash recipes in BTP without any problems.

Posted: Sun Oct 29, 2006 2:29 pm
by slothrob
I just found that, when I go back and edit a completed batch sparge schedule, I change the Mashout volume, hit OK and the Final Volume in the tun changes. The volumes drained, in the steps below, don't change. It looks like this is because the residual volume in my First Runnings Collection step changes to a negative number so the collected volume doesn't change.

I'm not sure if this as a bug or a feature.

I guess this is related to the idea of a lock box for the residual volume, now that I think about it.

Re: Saving Converted ProMash Files

Posted: Sun Oct 29, 2006 2:57 pm
by jeff
ColoradoBrewer wrote:I've run into a problem saving ProMash recipe files. Not sure if this is an actual bug, but I'll report what is happening anyway. When I try to save a recipe that was loaded from ProMash I get the following error message: "Assertion Failure: Assertion(!!(scrCharLens >0)) failed in output.cpp, line 995". My options are to Abort, Retry, or Ignore. I'm not sure if this is a bug because the subject files were ProMash Session files (.brw) converted within ProMash to recipe files (.rec). Now if I look in my folder of BTP recipes I will see the file, but when I try to load it I get an error that it is an invalid XML file (BTW, the file size is 0 bytes). I can save regular ProMash recipes in BTP without any problems.
If you send me files that give you difficulty I can take a look at them and see if I can find the cause. Most often problems are caused by junk characters that currupt the XML. Thanks!